Hey Thomas, yeah you could install and use the Access Door for RVs part # 37210-31015 the way you described and it would work well. It is waterproof so in the future it wouldn't leak either. view full answer...
Hi Norm,
The components at the front end of the MORryde RV Cargo Sliding Tray # MR89FR are all very close to being inline with each other. The lip on the tray sticks out the furthest and even then it's a negligible amount. MORryde doesn't list a clearance requirement but I'd give yourself at minimum 1/4" - 1/2" from the opening to avoid any issues. Most RV compartment doors sit flush with the wall because of the flange that prevents the door from swinging in so as long as you're behind... view full answer...
Hey Robert, thanks for the picture. It looks like the exact hatch is the part # D04-0471BKVP which may be slightly modified. I would attach the picture you sent in but it looks like maybe it was from a video that might have been copyrighted. view full answer...
Hi Donna,
If you don't have enough room then there are other handrail options available depending on the style of steps your RV has. For example, if you have pull-out steps then you could install the Stromberg Carlson Rail Mate Folding Handrail for RV Steps # AP-101. This handrail has a bracket that you'll bolt to the side of the steps to allow you to easily mount and remove it as needed. If you have a different style of steps then let me know and I'd be happy to look for a solution. view full answer...
Hey Kristopher,
Replacement parts for the Everchill RV Refrigerator w/ Freezer # 324-000119 will have to purchased through the manufacturer. Everchill recently sold to Lippert Components so if you give them a call they should be able to hook you up with the correct bins. view full answer...
There may be a way to get the Rear View Safety Backup Camera System # RVS-062710 to work if you have enough wire.
To wire these cameras properly you're going to need to connect the red to power, the yellow to the left turn signal, the brown to the right turn signal, the blue to the back/rear, and the black to a ground.
I'll go ahead and attach a wiring diagram as well for you to check out. view full answer...
So we do have the Replacement Leg for MORryde StepAbove RV Steps # MR36DR, Replacement Leg and Footpad for Lippert SolidStep # LC39AF as well as the All Terrain Landing Gear for TorkLift GlowStep Scissor Steps # TLA8000 depending on what steps you may have. If you have more traditional fold out steps I have typically seen the Stabil-Step Stabilizer Jack # JSS-7 used in those situations. view full answer...
The Replacement MaxxFan Plus 10-Speed Roof Vent with Smoke Lid # MA99FR is only compatible with the wall mount/remote (it says wall mount but can be used as a remote as well) Replacement Wall Control Panel for MaxxAir MaxxFan Plus Roof Vent # MA59FR.
So unfortunately it isn't compatible with the current remote you have. view full answer...
Hey Perry, so due to the door style that is at the rear of a 2023 Mercedes Sprinter the Inno tilt cargo carrier part # IN94MR wouldn't allow the door to open as it would sit up too tall even folded down but I do have a similar solution that would work.
You would need a carrier that swings away from the rear of the vehicle like the Yakima EXO part # Y62VR which would allow the rear door to open without interference. view full answer...
While we do carry Hinges # LC95VR, Latches # 295-000019, Gaskets # CS94VR and other parts for trailer doors we do not carry entire door assemblies. Based on your dimensions you will likely need to have a custom door built which you may be able to have done at a local trailer manufacturer in your area. view full answer...
Hey Jan, to locate the Torklift Generator carrier part # TLA7752 off-center in front of only one of the doors would require finding a welder/fabricator in your area who could add an additional hitch opening off to the side. This is such a rare request there isn't a product available for this specific application. view full answer...
Based on images I could find of Lark enclosed trailers with a double rear door it looks like you are going to need the Kit # PLR258-002. This will give you the mounts, handle, and catches for your trailer but you will need to source the 3/4" steel pipe and hardware needed locally and have the handle and cams welded to the pipe.
If you have something different from this type of setup please send me your images and dimensions for the parts you are looking to replace. view full answer...
Joe, your 2017 Ford Edge SEL can be flat towed and I'm going to get you setup with everything you'll need. The first thing you're going to need is a base plate - which is essentially the anchor point for your vehicle and the motorhome.
Personally, I'd go with anything Roadmaster that uses direct connection like # RM-524454-5. These guys have been pretty consistent in putting out a good product and they've been around a while so they've got the kinks worked out.
The next piece of the puzzle... view full answer...
The Bauer Products Motorhome Door Lock 402-112-000 # BA64FR has 1/4" diameter pins with 1/2" diameter on the ends of the pins. If this was not the pin size you needed please let me know as I did not see any pictures attached. view full answer...
Unfortunately Eugene, the door itself is not going to be something you can replace. You're going to need to replace the entire receptacle with the 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket # HM40975 or the CR Brophy Replacement 7-Pole, Trailer Connector Socket # R7CB if you just have a 7 way. view full answer...
Hey Jared, the Yakima Backswing bike rack part # Y02465 that you referenced does have the needed clearance to allow the rear door of your 2008 Dodge Sprinter to open. It has a distance of 15 inches from it's hitch pin hole to the back of the bike rack mast which is more than enough. view full answer...
Eric, the Lippert Patio Upgrade Kit for Toy Hauler Garage Doors # LC27FR weighs 116 lbs; but for the railing kit, we do not have those parts, unfortunately. view full answer...
Hey Luke,
Sorry about the confusion, and we can 100% get your 2007 Honda Civic 4-door sedan set up with all the parts needed for a Rhino-Rack roof rack, including both crossbars. You would just need these parts:
- Rhino-Rack Vortex Aero Crossbars # RRVA126B-2
- Rhino-Rack 2500 Series Legs # RRRLKVA
- Custom DK Fit Kit # DK152
This will have all the parts needed and give you a rack with both crossbars so you can haul your gear. view full answer...
HI Mason; thanks for writing in, though the only color the Multi-Purpose Access Door w/ Lock # 372E8102-A comes in is White. That said, it is designed to be painted if need be, so getting a coat of black paint on it is something you can do pretty easily. view full answer...